Features
- Virtually indestructible and unbreakable, mirror quality polycarbonate face
- Pure reflective coating
- Powder coated steel frame with unique tamper-proof design
- Recessed, tamper-proof fixings increase security and reduces ligature risk
- 7mm (9/32") Counter-bore holes designed to take security head fasteners
- Optional foam insert to enhance strength and longevity.
- Can be used in conjunction with CCTV to enhance effectiveness & safety
Suitable Uses
- In prison cells for safe inspection
- Observation of at risk patients in mental healthcare
- Visitaiton rooms for 180 degree viewing
- T-Intersections in corridors to avoid collisions
Specifications
International Product Codes
Mirror and Frame:
| Product Code | Size | Mirror Face | View Distance | Fixing Holes | Frame Colour |
|---|---|---|---|---|---|
| 17520HD | 450mm 18" | 3mm Polycarbonate | Up to 4m | 6 | Almond |
| 17537HD | 600mm 24" | 3mm Polycarbonate | Up to 6m | 7 | Almond |
| 17555HD | 900mm 36" | 3mm Polycarbonate | Up to 9m | 10 | Almond |
Optional Foam Insert:
| Product Code | Foam Insert Size |
|---|---|
| 21193 | 450mm 18" |
| 21194 | 600mm 24" |
| 21195 | 900mm 36" |
Usage Guides
Positioning
Installation Guide
Polycarbonate Half Dome Mirror and Frame Installation
NOTE: If installing with Rawl Spikes, it is recommended to use a punch. This is to eliminate damage to the mirror and powder-coated frame.
FOAM INSERTS: When installing the optional foam inserts DO NOT remove the grey or clear protective film on the inserts, as this may cause damage to the mirror face.
Suggested Fastening Methods
Installation: Drill a hole into the base material to a depth of at least 60mm.The tolerances of the drill bit used should meet the requirements of ISO/DIN Standard 8035. Blow the hole clean of dust and other material. Drive the Spike through the appropriate mirror face hole (and frame when used) ensuring the head is sitting firmly against the mirror or frame and recessed as shown in the above diagram.
NOTE: Care should be taken not to overdrive the Spike so as to cause damage to the powder coated surface of the frame. Finish off by applying (optional) a bead of non-pick sealant around the mirror or frame and the wall to prevent the secretion of small objects (eg razor blades etc).
DuraVision Rawl Spike Punch: The DuraVision designed punch for inserting spikes can significantly reduce the risk of damaging the mirror face and frame during installation.
Installation: It is recommended to use a 3/16” (4.76mm) Straight Shank Tanged Bit to drill the hole. The hole must be at least 2” or 50mm overall depth and free of any debris. By using the #27, 1/4” (6.35mm) Hex Bit the special Hi-Lo thread literally taps into masonry materials. The high,sharp thread with its notched cutting edge cuts deeply and easily. The alternating low thread provides stabilty for fast, accurate driving. Torx Tamperproof masonry screws are the optimal fastening solution for use in concrete, brick, or hollow block.
Download PDF Installation Guide View
Cleaning Guide
Polycarbonate Mirror Cleaning Guide:
General Cleaning:
DuraVision™ recommend cleaning their Polycarbonate Mirrors with soap and water and then with a soft, lint free, damp cloth.
DO NOT USE:
- abrasives
- acids
- solvents such as petrol and laquer thinners
Polish:
Use a non-abrasive polish, such Mr Sheen or Johnson's Pledge for a clear bright reflection.
Graffiti Removal:
Any graffiti should be removed from the mirror face as soon as possible and preferably within 24 hours. To remove graffiti, use a non-abrasive substance such as De-Solv-it Citrus Solution. Not all graffiti cleaning agents are suitable. Failure to use an approved cleaning agent may damage the mirror surface.
Powder Coated Frames:
Do not use harsh cleaning products or products that will leave a residue, as this will damage the powder coating, which protects the frame.
Download PDF Polycarbonate Mirror Cleaning Guide View
