Features

  • 2mm or 3mm acrylic mirror face
  • Pure reflective coating
  • Vinyl celuka back
  • Vinyl extrusion
  • Includes Outdoor J-Bracket to fix to wall or ceiling
  • Mounting screws Not included.
  • Pole mounting kit available

Suitable Uses

  • Driveways and Carparks
  • Outdoor Surveillance and Security
  • Industrial Safety
  • Cycle Lane Safety
  • Pedestrian Crossings and Sidewalks
  • Livestock Observation and Heat Detection
  • Swimming Pool Observation

Specifications

International Product Codes

Product Code Size Diameter View Distance Mirror Face Mirror Back Bracket Length
18026S 300mm Up to 21m 2mm Acrylic 10mm Vinyl 270mm
18044S 450mm Up to 28m 2mm Acrylic 10mm Vinyl 270mm
18062S 600mm Up to 38m 2mm Acrylic 10mm Vinyl 330mm
18078S 760mm Up to 46m 2mm Acrylic 10mm Vinyl 330mm
18114S 900mm Up to 55m 3mm Acrylic 10mm Vinyl 435mm
18118S 1200mm Up to 65m 3mm Acrylic 10mm Vinyl 435mm

Download PDF Information Sheet  View

US Product Codes

Product Code Size Diameter View Distance Mirror Face Mirror Back Bracket Length
68026S 12" Up to 70' 2mm Acrylic 10mm Vinyl 10 ½"
68044S 18" Up to 93' 2mm Acrylic 10mm Vinyl 10 ½"
68062S 24" Up to 125' 2mm Acrylic 10mm Vinyl 13"
68078S 30" Up to 150' 2mm Acrylic 10mm Vinyl 13"
68114S 36" Up to 180' 3mm Acrylic 10mm Vinyl 17"

Download PDF Information Sheet  View

Usage Guides

Positioning

traffic-1 traffic-2 traffic-3 traffic-4

Installation Guide

Outdoor Heavy Duty Convex Mirror Installation Guide:

  1. Decide the appropriate place to site the mirror to give maximum vision.

  2. Fix J-Bracket to wall, ceiling or pillar using suitable fixing hardware (ie: screws, bolts). Allowing enough room to get the mirror on to the J-Bracket.

  3. Remove the Adaptor from the J-Bracket.

  4. Thread Adaptor into the back of the mirror.

  5. Make sure the ventialtion hole is at the bottom, to allow moisture to drain.

  6. Peel protective film off around the immediate edge of the mirror.

  7. Slide the adaptor and mirror over the J-Bracket and adjust mirror to the desired position.

  8. Tighten the locking bolt on the adaptor securely.

  9. Totally remove protective film from the mirror face.

 

Installation:

J-Assembly1.jpg J-Assembly2.jpg J-Assembly3.jpg J-Assembly4.jpg

 

Optional U-Bolts:

U-Bolts1 U-Bolts2

 

Angle and Position:

Angle1.jpg Angle2.jpg Angle3.jpg Angle4.jpg Angle5.jpg

Download PDF Installation Guide  View

Cleaning Guide

Acrylic Mirror Cleaning Guide:

General Cleaning:
DuraVisionTM recommend cleanning their acrylic mirror faces with soap and water and then with a clean, soft, lint free, damp cloth. Use a non-abrasive polish, such as Johnson’s Pledge or Mr Sheen for a clear bright reflection.

Saturate a clean soft cloth with polish, then spray the mirror face with polish. Wipe the wetted cloth over the mirror surface. With a another clean dry cloth buff the mirror face until it is clear of polish.

DO NOT USE:

  • abrasives
  • acids
  • solvents such as petrol and laquer thinners

Graffiti Removal:
Any graffiti should be removed from the mirror face as soon as possible and preferably within 24 hours. To remove graffiti, use a non-abrasive substance such as De-Solv-it Stain Remover. Not all graffiti cleaning agents are suitable. Failure to use an approved cleaning agent may damage the mirror surface.

Scratches:
To remove scratches or repair blemishes on acrylic mirror faces only, use the following products:

  • For cleaning use NOVUS plastic polish #1
  • For fine scratches use NOVUS plastic polish #2
  • For badly scratched surfaces use NOVIS plastic polish #3 followed by #2 and #1.

Download PDF Cleaning Guide  View