Features

  • 2mm acrylic mirror face
  • Pure reflective coating
  • Large radius of curvature for minimum distance distortion
  • Red reflective markings on the frame for greater visibility
  • Very robust post clamp bracket for easy installation
  • ASA rectangular frame - ASA is a robust advanced plastic impregnated with 100% UV resistance
  • Wall mounting adaptor, optional extra

Suitable Uses

  • Road and Traffic Safety
  • High Visibility
  • Driveways and Carparks
  • Outdoor Security around Buildings
  • Security Checkpoints and Border Control

Specifications

International Product Codes

Product Code Size Diameter View Distance Mirror Face Mirror Back Bracket Length
18642R 600x400mm Up to 38m 2mm Acrylic ASA Vinyl 75mm dia. Pole Clamp
18645R 800x600mm Upt o 50m 2mm Acrylic ASA Vinyl 75mm dia. Pole Clamp
18648R 1000x800mm Over 50m 2mm Acrylic ASA Vinyl 75mm dia. Pole Clamp

Download PDF Information Guide  View

Usage Guides

Positioning

traffic mirror 1 traffic mirror 2

Installation Guide

Outdoor Pro Series Acrylic Installation Guide:

 

Installation to 75mm Pole.

  1. Decide the appropriate place to site the mirror on a 75mm pole.

  2. Fix clamp and mirror mount assembly to the pole.

  3. Make sure adjustment slot is to the bottom

  4. Peel protective film off around the immediate edge of the mirror.

  5. Fix the mirror to the clamp bracket assembly.

  6. Make sure the ventilation hole is at the bottom to allow moisture to drain.

  7. Once the desired position has been found, tighten the bolts and nuts securely.

  8. Totally remove protective film from the mirror face.

 

Clamp-Assembly1.jpg Clamp-Assembly2.jpg Clamp-Assembly3.jpg

 

Installation to an Extra Large Pole (With Optional Wall Mount Adaptor)

  1. When mounting to an extra large pole (eg: Power Pole, Lamp Post, Large Piller) use steel strapping to secure the Wall Mount Adaptor to the large pole.

  2. Fix clamp and mirror mount assembly to the Wall Mount Adaptor, as below (see Wall Mount Adaptor Installation).

Wall Adaptor 5 Wall Adaptor 6

 

Optional Wall Mount Adaptor:

  1. Decide the appropriate place to site the mirror on a flat surface (wall, fence, building etc).

  2. Fix Wall Mounting Adaptor using appropriate screws.

  3. Fix clamp and mirror mount assembly to the Wall Mount Adaptor.

  4. Make sure adjustment slot is to the bottom

  5. Peel protective film off around the immediate edge of the mirror.

  6. Fix the mirror to the clamp bracket assembly.

  7. Make sure the ventilation hole is at the bottom to allow moisture to drain.

  8. Once the desired position has been found, tighten the bolts and nuts securely.

  9. Totally remove protective film from the mirror face.

Wall Adaptor 1 Wall Adaptor 2 Wall Adaptor 3 Wall Adaptor 4

Download PDF Installation Guide  View

Cleaning Guide

Acrylic Mirror Cleaning Guide:

General Cleaning:
DuraVisionTM recommend cleanning their acrylic mirror faces with soap and water and then with a clean, soft, lint free, damp cloth. Use a non-abrasive polish, such as Johnson’s Pledge or Mr Sheen for a clear bright reflection.

Saturate a clean soft cloth with polish, then spray the mirror face with polish. Wipe the wetted cloth over the mirror surface. With a another clean dry cloth buff the mirror face until it is clear of polish.

DO NOT USE:

  • abrasives
  • acids
  • solvents such as petrol and laquer thinners

Graffiti Removal:
Any graffiti should be removed from the mirror face as soon as possible and preferably within 24 hours. To remove graffiti, use a non-abrasive substance such as De-Solv-it Stain Remover. Not all graffiti cleaning agents are suitable. Failure to use an approved cleaning agent may damage the mirror surface.

Scratches:
To remove scratches or repair blemishes on acrylic mirror faces only, use the following products:

  • For cleaning use NOVUS plastic polish #1
  • For fine scratches use NOVUS plastic polish #2
  • For badly scratched surfaces use NOVIS plastic polish #3 followed by #2 and #1.

Download PDF Acrylic Mirror Cleaning Guide View